Laboratory Peristaltic Pumps operates by pumping fluids through the Peristaltic Pump tube squeezed rotating rollers in the pump head that squeeze the liquid out of the tube with compression force.
The peristaltic pump is a liquid delivery device that can control the flow rate. It has the characteristics of high delivery accuracy, strong corrosion-resistance, small shearing effect, simple operation, easy maintenance, and can effectively avoid cross-contamination. It has a very wide range of laboratories. Applications. From cell culture to in vitro organ research, from material preparation to water treatment technology optimization, from food ingredient extraction to food preparation technology improvement, Peristaltic Dosing Pumps may be used as power to achieve accurate fluid transmission and processing operations during the experiment.
Laboratory Peristaltic Pumps,Lithium Mining Peristaltic Pump,Liquid Additive Peristaltic Pump,Drugs Dispensing Peristaltic Pump Baoding Chuangrui Precision Pump Co., Ltd. , https://www.crprecisionpumps.com
Alfa Laval offers standard and specialty centrifugal pumps for highly hygienic industries such as the pharmaceutical and food industries. SolidC pump is a newly developed pump for standard applications. Depending on the capacity and cost, the pumps can be divided into pumps for standard operation and pumps for special applications. If a manufacturer wants to provide both a standard application pump and a high performance pump for the health sector, all of his pumps must meet the quality and structural design standards in this area. In general, the standard performance of the pump performance specifications are as follows: the inlet pressure to reach 4bar, the temperature up to 120 ℃, the viscosity range of about 150cP. Selection is decisive In order to achieve the specific purpose of use, select the correct, suitable pump at any time is very important. The only way to ensure the best operation of the device to meet customer requirements and minimize costs, as well as the standard pump. Because for the user, the total cost (sum of pump investment, installation, operation and maintenance costs) is always the most important. At the same time, the standard pump also meets the high demands of product protection, cleaning and production in operation. In the design of the SolidC pump, the following points have been noticed in particular: In addition to the modular construction, many components of all sizes are used; delivery times are shortened as standard; flexibility (for easy installation and storage) And a good overall price. Product Protection Matters Customers in the health arena place great importance on product protection when delivering products and generally require that all equipment components be well-cleaned. By means of advanced structural design and computational tools can be done SolidC these requirements: small tolerances due to the internal structure of the impeller and special structure, can achieve good flow properties to ensure simultaneous protection of product delivery, improve efficiency and device capabilities. In spite of this, enough clearance is left to ensure effective cleaning with the CIP method. The pump complies with German national hygiene standards and also meets the 3A and EHEDG standards. The pump's key structural features are as follows: All parts in contact with the product are 316L or 1.4404 stainless steel; the surface is smooth, there is absolutely no dead angle in the key parts; the provisions of the O-ring sealing section compression; O-ring groove Designed to withstand vacuum and pressure shocks; Fully open impeller with hygienic o-ring seal, suction tube without throttling (no shrinkage); Stainless steel fitting and guard (hygienic, non-corrosive) . Shaft sealing is a key point for all pumps. To meet the minimum number of downtime requirements, this standard pump uses a particularly advanced seal: an external (shaft end) unloaded (decompression) shaft seal for a special series of pumps that are difficult to operate. This is done so that only one type of shaft seal can be used for all pumps in the series. The advantages of this design result are summarized as follows: All structural pumps have only one seal (simplified storage); unloading seals that are immune to pressure changes or pressure shocks; proven, long structural life; Reduced wear; Retaining ring (lock ring) on ​​the rear wall; External seal free from media influence. Simple maintenance, reduce costs Industrialization process is constantly improving, the parking time needs to be shorter and shorter. Therefore, special care must be taken in the design of standard pump applications for simple and quick repairs to replace the shaft seal and O-ring in a particularly short period of time, within 10 minutes. In this way, pump users can significantly reduce pump maintenance costs. SolidC pumps are also advantageous in this regard: Sealing can be placed from the front; couplings are easy to set up and adjust; clamping-connected pump housings; easy to replace from unidirectional shaft seals to unidirectional flushing shafts Sealed complete kit; pump housing is free to rotate 360 ​​°. It is important for the user to know what pumps are needed and which ones to pay special attention to when selecting pumps for normal operation and high performance specialty applications.