Anti Corrosion Zinc Rich Pure Epoxy Base Powder Coating

Anti Corrosion Zinc Rich Pure Epoxy base Powder Coating

Details:
This is an epoxy-based smooth  satin coating with  a high level  of zinc,  providing excellent corrosion protection while  improving the adhesion properties  of powder topcoats  resulting in superior  service life and film integrity. It is not recommended for exterior use without a topcoat,typically used for garden tools,industrial waste equipment,agricultural  machinery, pipeline coatings, electrical  switch gear,cabinets and cable ducting.

Properties:
It is higher  average specific gravity than standard  powder coatings, therefore box feeders and
fluidizing hoppers will need to be tested to ensure adequate mixing. It may require increased air pressure
or vibration levels than standard powder coatings.

AVERAGE COVERAGE

8-12 square meters / kg, thickness 60 microns (100% of the powder coating utilization rate)

PACKING

Outside carton lined with two layers of polyethylene bags, each containing 20 kg or 25kg net weight.
 

• RAL colors coating powder
• Pantone colors
• Color-matching regarding customer requirement is available
•  

GENERAL TYPES

• Polyester /Hybrid powder coating
• Epoxy Powder coating color
• Metallic powder coating color
• Hammer tone color powder coating
• Texture color powder coating powder

Textures include sand grain, hammer, silk pattern, sand textured, marble,metallic, multi-color.
 

PHYSICAL PROPERTIES

• Specific gravity :1.2 ~ 1.8g/cm3 up to colors
• Particle size distribution:100% less than 100 microns (depending on the specific indicators art effects may be, according to the special requirements of painting adjusted)
• Level of liquidity:24 ~ 27 mm
•  

CURING CONDITIONS

180 °C ~ 200 °C (work piece temperature), 10-15 minutes
 

STORAGE AND TRANSPORT

Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure.Storage products in line with the above conditions, since the date of production, effective storage period is 6 months.Over the storage period may be re-tested and the results were consistent with, can still be used.
 

HEALTH AND SAFETY

Coating powder is a non-toxic products, but should be avoided in the course of inhalation of dust.Proposed operators wear appropriate dust mask, glasses.If possible, try to avoid long-term skin contact with powder coating
We offer free samples to you.

You can contact me informatoin as follows,
Attn:Danae

Anti Corrosion Zinc Rich Pure Epoxy base Powder Coating

Details:
This is an epoxy-based smooth  satin coating with  a high level  of zinc,  providing excellent corrosion protection while  improving the adhesion properties  of powder topcoats  resulting in superior  service life and film integrity. It is not recommended for exterior use without a topcoat,typically used for garden tools,industrial waste equipment,agricultural  machinery, pipeline coatings, electrical  switch gear,cabinets and cable ducting.

Properties:
It is higher  average specific gravity than standard  powder coatings, therefore box feeders and
fluidizing hoppers will need to be tested to ensure adequate mixing. It may require increased air pressure
or vibration levels than standard powder coatings.

AVERAGE COVERAGE

8-12 square meters / kg, thickness 60 microns (100% of the powder coating utilization rate)

PACKING

Outside carton lined with two layers of polyethylene bags, each containing 20 kg or 25kg net weight.
 

• RAL colors coating powder
• Pantone colors
• Color-matching regarding customer requirement is available
•  

GENERAL TYPES

• Polyester /Hybrid powder coating
• Epoxy Powder coating color
• Metallic powder coating color
• Hammer tone color powder coating
• Texture color powder coating powder

Textures include sand grain, hammer, silk pattern, sand textured, marble,metallic, multi-color.
 

PHYSICAL PROPERTIES

• Specific gravity :1.2 ~ 1.8g/cm3 up to colors
• Particle size distribution:100% less than 100 microns (depending on the specific indicators art effects may be, according to the special requirements of painting adjusted)
• Level of liquidity:24 ~ 27 mm
•  

CURING CONDITIONS

180 °C ~ 200 °C (work piece temperature), 10-15 minutes
 

STORAGE AND TRANSPORT

Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure.Storage products in line with the above conditions, since the date of production, effective storage period is 6 months.Over the storage period may be re-tested and the results were consistent with, can still be used.
 

HEALTH AND SAFETY

Coating powder is a non-toxic products, but should be avoided in the course of inhalation of dust.Proposed operators wear appropriate dust mask, glasses.If possible, try to avoid long-term skin contact with powder coating
We offer free samples to you.

You can contact me informatoin as follows,
Attn:Danae

Super 200 – a series of Macroporous Adsorbent Resin designed for the separation for pharmaceuticals and natural products. These resins provide customers a wider choice of the conditions for process development and optimization to achieve higher purity and better yield. Its outstanding chemical stability has been proven to meet the requirements of Cleaning-in-Place (CIP) in FDA regulation. They are made of polystyrene, with the advantages of high loading capacity; high selectivity; cheaper CIP procedure; long life-time; low back pressure; stable column bed and high mechanical strength.

150-350 Micron Macroporous Adsorbent Resin

150 Micron Macroporous Adsorbent Resin,350 Micron Macroporous Adsorbent Resin,200 Micron Macroporous Adsorbent Resin,Alternative Chloromethyl Polystyrene Resin

Nanjing Genshine Bio-technology Co., Ltd , http://www.genshine-bio.com